maanantai 11. helmikuuta 2019

SORMUS PROJEKTIT
(RING PROJECTS. ENGLISH VERSION BELOW)

Ajattelin kokkeilla tehä pari sormusta ku tyttö halus. Se ei ollu päässy teknisen tunnille koulussa jossa ne oli niitä väännelly, nii se sitte sano mulle että SAAN tehä sille semmosen... tai 9kpl semmosia 😂

Kattelin nuita mutteri varastoja ja löysinki pari sopivaa testi yksilöä.

MUTTEREITA
Ensimmäinen oli tuommonen liitin mutteri.

Tämähän on jottai messinkiä nii sitä oliki meleko helppo muokata.
Vähän rälläkkällä kapeammaks ja sitte tremelillä ulko reunat ja sisäreikää tasasemmaks. Yhden sivun jätin että sain kantasormuksen mallin.

RÄLÄKÄLLÄ SUPISTUS MUTTERISTA POIS
TREMELILLÄ REUNAT PYÖRIÄKSI JA SISUS TASASEKSI
SORMUKSEN MUOTO VALMIS
Loppuha oliki sitte käsin hiontaa hiekkapaperilla ja viimeistely vesihiomapaperilla (1000 karkeus)

MUTTERISORMUS VALMIS
Hyvähä siitä tuli, vaikka vaan tunteroinen meniki. Aika pieni oli tässä sisämitta, mutta tais mennä tytölle pikkurilliin 😆Melko pehmeää työstettävvää tuo messinki ja jättää vihreää jälkeä sormeen... Eli sitte seuraava sormus

Pikkusen putsailla entisiä rautapölyjä pois tasolta, ja tämä kikkahan yleensä unohtuu.
Magneetti johonki liinaan käärittynä ja sillä pyörittelee tasot läpi. Sitte vaa magneetit pois ja rauta pöly tippuu liinasta.

MAGNEETTI PUHDISTIN
50sentin kolikosta kuulemma tullee helposti sormus...

50 SENTIN KOLIKKO
Tässähä ei niin kovin kummosta kuviota oo nii päätin tehä siliän sormuksen.
Mulla vaa ei kovin hyvät työkalut oo, mutta kyllähä sitä aina jottai keksii 😉

Porasin tuohon 50senttisen keskelle reiän

REIÄN TEKO KOLIKKOON
Aattelin että mitä isompi nii sen helpompi on sitte isontaa sitä sisäreikää ku ulkokuori on valmis
Pultti läpi sormuksesta ja takoa vasaralla se littaan

PULTTI KOLIKKOON JA TAKOMAAN
Nuissa videoissaha kaikilla on jotku pylväsporakoneet ja ihan sormuksia varten olevat levittäjät.
Mullaha ei ollu nii piti koittaa saaha se tuossa ruuvipenkissä isommaks.
Kyllähä se siitä pikkuhiliaa isoni. Ensin poranterällä ja sitte tremelillä loput.
Tuossa hommassa vaa oli semmonen vika että ku reikä isoni nii piti vääntää penkkiä kiriämmälle, ja miten siinä nyt käykää ku puristaa ohutta pyöriää kappaletta jossa reikä keskellä... soikiaksiha se mennee 😆

SISÄREIÄN ISONNUS
Siinä meni meleko monta tremelin hionta terää ja monta kertaa palo sormet, mutta lopuksi se oli tarpeeks iso että se mennee tytön sormeen. (noin 17millinen, työntömitalla mitattuna)

Sitte pultin ympärille jesaria ja sormus siihen pyörimään. Hiomapaperi käteen ja hiomaan.

KARKEA JA HIENO HIONTA
Pitihän se sisältäki saaha vielä sileämmäks, nii sitte pulttiin kiinnkki jesarilla hienoa hientapaperia nii että se pyörii ulkopuolella.

SISÄHIONTA
Reunoille hionta vielä raudan päällä ja Done.
Mulla ei oo mittää kiillotusainetta nii se nyt sai jäähä tuommoseks 😒 Mutta ei se paha oo nuinkaa.

50 SENTIN KOLIKKO SORMUS
Pikkusen jäi reunoille kuviota, mutta en halunnu niin kapeaksi että oisin ihan kaikki hionu pois. Tähän ois muuten auttanu jos en ois porannu niin isoa reikää keskelle, ja takonu pienemmän pultin kans kolikon läjään 😔

Sitte ajattelin tehä vielä 2€ tai 10markan kolikosta sormuksen ku niitä vaimolla loju tuolla jemmassa 3kpl. Olihan ne joutsen kolikoita, mutta ihan tavallisia semmosia 😉 eli arvoa ei oo ku se 4€ / kpl, Mutta ku niillä ei oo arvoa ku keräilijöille nii aattelin sitte "tuhota" semmosen

10 MARKAN KOLIKKO (1995 Joutsen kolikko)
Tästähä lähti ihmeen hyvin tuo keskusta irti. Pikku napautus ja ei muutako hommiin.

KOLIKON IRROTUS
Ajattelin että saan väännettyä tuon reunuksen sillai että sais nuo lehdet jäämään tuohon päälle kauniisti.
Piti ettiä vähä tietoja että miten se sormuksen kääntö tapahtuu, ja löysinki Youtubesta videon.
Eihä mulla ollu semmosta piikkiä niinku nuissa videoissa, nii päätin tehä jonkumoisen ite.

PIIKIN TEKO
En jaksanu sitte sen enempää kaventaa tätä ettei mulla lopu kaikista konneista kaikki hioma päät 😅

Lämmitin kolikkoa vähän sytkärillä että pehmenis (Kunnon toho ois ollu hyvä)

KOLIKON LÄMMITYS
Eikä mulla oo kumi / puuvasaraa, nii pätkin sitä sitte tuommosella puun pätkällä... Ei onnistunu.
Tämä mun piikki oli liian paksu, nii sehä lipes siitä kokoajan.

KOLIKON KÄÄNTÖ (YRITYS)
Sitte tuli mielee että sopivalla räikkä hylsyllähä se mennee.
Vähä kangasta vällii ja pätkiin vasaralla... Hohhoijaa

HYLSYLLÄ LEVENNYS
En laittanu tarpeeks kangasta välliin nii sehä meni siitä läpi ja naarmutti kunnolla tuota kolikon kuviointia.
Hermotha siinä meni nii päätin sitte että kuviot saa lähtä. Hylsyllä vaa nii palio ku meni, ja sitte toisinpäin kolikko ja sama homma.

Nyt se oli sormuksen näkönen.

Tämä ulompi osaha o meleko iso, nii en palio ennää uskaltanu sisäpuolelta hioa sitä.
Ulkopuoli sileäks ja reunat hiekkapaperilla suoriksi. Sitte taas vesihiomapaperia ja valmis.

ULKOPUOLEN HIONTA
Sisäpuolelle pikkusen jäi näkyviin vielä SUOMI FINLAND teksti 😊

10 MARKAN SORMUS VALMIS
Onhan se aika rujo, mutta en ajatellu käyttää enempää aikaa fixaamiseen ku en tienny että menneekö tuo kellekkään... on muute senverran iso

Tässähä tuli meleko monta kämmiä. Hiekkapaperi tarttu kankaaseen, sormus väänty, sormet palo, ym... Liitän ne videon loppuun 😅

HUOM. Näistä kolikko sormuksista muuten irtoaa jottain ainetta elimistöön mikä ei oo hyväksi. Niihihän voi laittaa jonkulaisen lakan, mutta seki kuluu ajankans pois, ja käsittely on uusittava! Mää nyt käytän alkuun vaan kynsilakkaa.

Mullaha oli vielä tuo keskiosa 10markan kolikosta. Siitähä saa helposti riipuksen.

10 MARKAN KOLIKON KESKUSTA
Poralla reikä yläreunaan ketjua varten
Sitte ajattelin jättää tuon joustenen kuvam ja hioa tuon 10 kuvan pois.
Pikkusen se oli vääntyny ku sen löi irti, nii sai pikkusen aikaa hioa että kuviointi lähti pois.

KESKUSTAN HIONTA
Kaiversin sitte sydämmen riipukseen ku en muuta keksiny ja lisäsin ketjun.

KAIVERRUS
VALMIS
Tuo sormusha oli aivan liian iso mulle nii annoin sen sitte isälle lahjaks, ja riipusha meni sitte tietenki äidille 😊

Sitte vielä yks kokeilu mutteri versio.

En tiiä miten tuon tallin saa nii sekasin ettei mittää löyä... Tai no kaikkiha o just siinä missä pittääki, mutta ne o aina liian lähellä ettei löyä tavaroita 😄

Kävin ihan vartavasten näitä ostamassa lisää. On kyllä ajatuksissa tehä muitaki mutterivehkeitä ku pinterestistä sai niin hyviä ajatuksia 😉, mutta tämä sormus.

MUTTERI
Tätähä piti kaventaa aika rankasti rälläkällä, ja kierteet tietenki kovertaa pois (Ettei tarvi kiertää sormeen 😅)
Ensin alotin tuosta sisäpinnasta. Poralla ja tremelillä tasasemmaks sisäpintaa.

KOVERRUS
KAVENNUS
Tuosta pikkupalastaha ois kan saanu sormuksen, mutta en jaksanu ruveta värkkää 😄
Sitten ulkopinta. Ajattelin että teen tuohon päälle vähän kuviota nii annan jäähä sen vähän paksummaks siitä kohalta.

PYÖRISTYS
Rälläkkään kivilaikka ja sillä isoimmat pinnat pyöriäks. Sitte tremelillä loppu silaus
Pulttiin sai hyvin tuon sormuksen kiinni, ja ku katkas tuon pään nii sen sai sitte tuohon poraan mahtumaan.

PULTTI KIINNITYS
Hionta poralla ja samalla tein tuohon keskelle tuommosen uran viilalla, antamaan vähän muotoja.

KUVION TEKO
Vielä pyöräytys vesihiomapaperilla ja valmis. Mullaha ei ollu sitä kiillotus ainetta nii muistin että joskus puutöissä pyöritin puulla puuta vasten ja se rupes kiiltämään, se toimi myös tässä hommassa 😉


SORMUS VALMIINA
Pitihä se kaivertaa sydän tuonnekki, ku o kerta rakkaudella tehty 😄

Siinäpä ne. Nyt sai sormushommat taas riittää. Ei saanu tyttö 9kpl sormuksia, mutta saa tehä ite loput jos haluaa 😆. Jos enskerralla tekis niitä mutteri pultti viritelmiä 😉
Saisha nuista tosi siistejä ku käyttäs enemmä aikaa ja kunnon vehkeillä tekis, ehkä saatan palata tähän aiheeseen... joskus

Laitoin parit pilaversiotki videoon. kaykäähä kattelee. Tuossa linkki (Suomenkieliset tekstit):
https://www.youtube.com/watch?v=XRM0GXF3qco&feature=youtu.be

Katellaampa taas 😘
________________________________________________________________________________________________________________________________________________________

RING PROJECTS. (ENGLISH VERSION)

I thought to try and make few rings cause our girl wanted. She didnt get to go tecnic class when they did the rings so she sayd to me that i have to do it for her... or 9 of them 😂

I looked if i have any suitable nuts in sorage and found few of them.

NUTS
First i tryed with connectir nut

It was a brass nut so it was easy to modificate
I used grinder to narrow it and tremel to get the edges of and smoothen the inner nut. I left one side untouched so i could get the basering look

GRINDER TO GET THE REDUCTION OFF
TREMEL FOR THE EDGES AND SMOOTHING THE INNER RING
BASERING SHAPE READY
Last i sanded the ring with sandpaper and the smoothing whit 100grade water sandpaper

1ST NUTRING READY
It came out good for my first ring, and i used about hour for that. The size was prettu small, but i think our daughter can but it to littlefinger 😆 Its pretty soft stuff and leaves some green markings to finger... Next ring then

I had to remove some old iron dust from the worktop, and this is the trick that i always forget. But magnet inside some clothing and sweep the table with it. Then just remove magnet and the iron dust falls where you want it to fall.

MAGNETIC CLEANER
50Cent coin can be easily made to ring, i heard...

50 CENT COIN
This one doesnt have any good shapes so i thought i made smooth ring from this.
I dont have any prper tools, but i can figure always something out 😉

I drilled hole to coin

HOLE TO COIN
I thought that if the hole is bigger its easyer to make the inner hole suitable.
Bolt trough the ring and hammer it flat.
BOLT TO RING AND BOUND IT WHIT HAMMER
Those youtube videos everyone has somesort of pillar drill and some sort of spreaders.
I dont have any of those so i had to try and make the hole bigger in the bench.
It was pretty hard but finally managet it. First whit big drill piece and then tremeld the rest.
In that part there was just one proplem. When i made the hole bigget the ring cave in and turned oval😆

INNER HOLE BIGGENING
I lost many tremel heads and burned my fingers many times, but finally get it to 17 millimetre size

Then i used drill. Some tape ovet the drillpit and ring there thightly. Rotate the drill and use sandpaper to smoothen the top.

ROUGH AND FINE SANDING
It had to smoothen inside too, so i taped the sandpaper to drillpit so that it would rotate when u hold the ring on it.

INNER SANDING
Sanded the edges over the ironbar that i had and Done
I didnt have any polishing stuff so i left it like this 😒 Its not that bad  like that

50 CEN COIN RING
There was some pattern at the outer ring but i didnt want to sand it anymore, so it wouldnt go too thin. It would of helped if i didnt drill so large hole in coin, and flatten it with smaller bolt 😔

Then i thought i make ring out of 2€ or old 10 Mark coin. i used 10 mark cause wife had 3 of them at the jewelrybox. They were swan coins but regular ones 😉 so value was about 4€. well the 4€ value is for collectors so i thought i ude one of them.

10 MARK COIN (1995 swan coin)
The center was pretty easy to get of, just a little tap and off to work
COIN REMOVAL
I thought i could make the ring so that the leaves would stay beatifully to top.
I had to search some info how to turn the coin, and found few at the youtube.
I didnt have the spike that they used so i thought i make one myself

SPIKE MAKING
I couldnt narrow it enough. I thought i save some grinding tips for later 😅

I heated the coin whit lighter a bit so it would be softer (Proper heater would be nice)
COIN HEATING
Didnt have any rubber or wood hammer so i tryed to beat it whit piece of wood... Didnt work
My spike was too thik so the ring just slipped all the time.

RING TURN (Try)
Then i got the idea to use right size wrench socket.
Some cloth between and hammered it... Oh shi#%¤

WRENCH SOCKET TOOL
I didnt use enough cloth so the socket pushed throug it and scraped the ring good.
I lost my nerve and desided that the leaves can go off. I just puonded whit the socked so that it did turn, and then flipped the coin and the same thing again

Now it started to look like ring

This outer piece was so big that i didnt want to larger it anymore.
Smoothen the outside and danded the edges. Last sanding whit waterpaper and done.

OUTSIDE SANDING
Inside theres still a bit text that says SUOMI FINLAND 😊

10 MARK RING, DONE
Its pretty rough, but i didnt want to use anymore time with it because i didnt know if anyone would have so big fingers... thats pretty big btw

In this one i had many bloobers. Sandpaper got stuck to cloth, ring bended, fingers burned exetera... i put the bloobers at the video 😅

ATTENTION! From these coin rings, theres some chemical that dissolves to your body thats not good for your health. U could use some varnish, but it will fade and u have to repeat the treatment. I will use some nailpolish for now.

I still had that center piece from the coin, i could make some pendant out of that.

10 MARK COIN CENTER
Drilled hole for chain at the top.
I thought i leave the swan to it and sand the 10mark picture out of it.
It was pended a bit when i hit it and had to sand some tme to get the picture off.

CENTER SANDING
I did engrave heart to it cause didnt figure anything else and added chain for it

ENGRAVING
DONE
That ring was way too big for me so i gave it to my father, and the pendant went to my mother 😊

Then there was one nut that i wanted to make.

I dont know how i get that carage so messed up that i cant find any tools... Tools are where they suppose to be, but mayby they are just too close, so i cant find anything  😄

I did buy more of these from store cause i have some other bolt and nut stuff to do. I got the idea from pinterest 😉... But this ring

NUT
These had to narrow pretty much with grinder and remove the spiral (So u dont have to raotate it to your finger 😅)
First i started with the inner spiral. Drilled it bigger and smooth the last with dremel.

GOUGE
NARROW OFF
Then there was uot side of the ring. I thought i leave it thikker so i can make some pattern there.

ROUNDING
Grinded the bigger stuff whit stonedisc and then used tremel for the smaller defects. I cutted one bolt and mounted the ring there so i could get it to fit my drill.

BOLT MOUNTING
Rotated the drill and used sandpaper to sand the edges off. Then i used file to make some shape at the middle of the ring

SHAPE MAKING
Used waterpaper for the last smoothing. Because i didnt have any polishing liguide i used wood. I remembered when i used wood on wood to make the surface shine, and that worked here too 😉

STEEL RING DONE

STEEL RING DONE
Had to carve heart there too, bacause its made from love 😄

Thats that. Now im done whit the rings. Our girl didnt get the 9 rings, but she can do the rest if she wants 😉. Next time i think i make the nut and bolt weldings, have to try at least 😄
You could get really niceones from these if you just put in the time. mayby i come back to this subject... someday

I but few bloobers to video. Heres link for it, check it out (English video):
https://www.youtube.com/watch?v=XRM0GXF3qco&feature=youtu.be

Be seeing you 😘





Ei kommentteja:

Lähetä kommentti